http://control.zebrix.net/doc/ 2026-06-19T17:17:39+00:00 http://control.zebrix.net/doc/ http://control.zebrix.net/doc/_media/logo.png text/html 2025-08-14T12:57:38+00:00 Anonymous (anonymous@undisclosed.example.com) http://control.zebrix.net/doc/en:start:first_alert?rev=1755176258&do=diff Your First Alarm Now that we are monitoring our first piece of equipment using the Ping driver, we will set up an alarm to track the status of this equipment. An equipment’s status can change based on the alarms you configure. In this example, we will instruct zebrix control to mark the equipment as text/html 2026-05-27T14:13:58+00:00 Anonymous (anonymous@undisclosed.example.com) http://control.zebrix.net/doc/en:start:first_equip?rev=1779891238&do=diff Your First Equipment We will now add and monitor your first piece of equipment using Zebrix Control. To begin, we’ll use a simple example: a device on your network that we will monitor via a basic ping. You will need its IP address. Adding the Equipment text/html 2025-07-29T14:05:54+00:00 Anonymous (anonymous@undisclosed.example.com) http://control.zebrix.net/doc/en:start:first_incident?rev=1753797954&do=diff Your First Incident In Zebrix Control, an incident refers to sending a status change notification through a communication channel. An incident is based on three key components: * Notification Channel: Configures the communication method used (e.g., email, SMS, etc.). text/html 2025-01-28T15:48:07+00:00 Anonymous (anonymous@undisclosed.example.com) http://control.zebrix.net/doc/en:start:first_login_google?rev=1738079287&do=diff Login with a Microsoft Account * Go to <http://control.zebrix.net> * Enter your username, you will be automatically logged in or redirected to your Microsoft login page. Once your authentication is successful, you are logged into Zebrix Control. text/html 2025-01-28T15:48:07+00:00 Anonymous (anonymous@undisclosed.example.com) http://control.zebrix.net/doc/en:start:first_login_local?rev=1738079287&do=diff Connect with a local account * Go to <http://control.zebrix.net> * Enter your username, you will be redirected to the local login page: - Click on “Forgot password” - Submit your request. You will then receive an email with a link to set your password. text/html 2025-01-28T15:48:07+00:00 Anonymous (anonymous@undisclosed.example.com) http://control.zebrix.net/doc/en:start:first_login_microsoft?rev=1738079287&do=diff Login with a Microsoft Account * Go to <http://control.zebrix.net> * Enter your username, you will be automatically logged in or redirected to your Microsoft login page. Once your authentication is successful, you are logged into Zebrix Control. text/html 2025-01-28T15:48:07+00:00 Anonymous (anonymous@undisclosed.example.com) http://control.zebrix.net/doc/en:start:first_login?rev=1738079287&do=diff Your First Login to Zebrix Control The procedure for your first login to Zebrix Control depends on the type of authentication set up by your administrator. If you have any questions or need assistance, don’t hesitate to reach out to them for support. text/html 2025-05-15T10:34:17+00:00 Anonymous (anonymous@undisclosed.example.com) http://control.zebrix.net/doc/en:start:first_probe?rev=1747305257&do=diff Your First Probe You should have received your first probe in the form of a device to connect to your network. If not, you can install one yourself using this guide Probe install To set up the probe: * Connect it to your network. * Plug in the power supply. text/html 2026-02-24T10:18:38+00:00 Anonymous (anonymous@undisclosed.example.com) http://control.zebrix.net/doc/en:start:start?rev=1771928318&do=diff Getting Started Welcome to Zebrix Control. Follow the steps below to quickly configure your environment and become fully operational. Setup Steps * First login Access your administration interface. * First probe Deploy your probe on the network to enable equipment supervision.